Roofing calculator: how many long-span or corrugated GI sheets

To count roofing sheets in the Philippines, divide the roof length by the sheet's effective width: 1.00 m for long-span rib-type, cut to the slope length plus 5 cm, or 0.70 m for corrugated GI (a 0.80 m sheet with a 1½ corrugation side lap), with 0.25 m end laps up the slope. Then multiply by the number of roof sides. A 10 m gable roof with 4 m rafters at a 4:12 pitch takes 20 long-span sheets 4.27 m long, or 60 corrugated sheets of 8 ft, plus 36 C-purlins, about 600 to 680 tek screws and 5 ridge rolls.

Quick answers

Question Answer
Effective width of a long-span sheet 1.00 m (some profiles 1.07 m or 0.98 m), sold by the metre
Effective width of a corrugated GI sheet 0.70 m with a 1½ corrugation lap; 0.60 m with 2½ (0.80 m sheet)
Corrugated GI sheet lengths 5 to 12 ft; 8 ft is the usual default
End lap between corrugated sheets 0.25 m (about 10 inches)
Tek screws per m² of roof 8 for corrugated GI; 7 for long-span
Purlin spacing 0.60 m; one 6 m C-purlin covers about 5.8 m
Ridge rolls for a 10 m ridge 5 rolls of 2.4 m (10 ÷ 2.25 m, rounded up)
Slope factor for a 4:12 pitch × 1.054 (3:12 is 1.031; 6:12 is 1.118)

Screws per m², the ridge-roll lap and one downspout per 10 m are rules of thumb, not PH manufacturer data. Purlin spacing must follow your structural plans.

Calculator

Estimate roofing sheets, purlins, tek screws and ridge rolls. Open the roofing calculator in Countstruct.

How to estimate it

  1. Calculate slope length from pitch

    Multiply plan horizontal rafter runs by the pitch multiplier √(1 + (Rise ÷ Run)²). Standard residential pitches include 3:12 (factor 1.031), 4:12 (1.054), and 6:12 (1.118):

    Slope Length = Horizontal Rafter Run × Pitch Factor

  2. Determine sheet coverage and layout

    Choose your roofing profile:

    • Corrugated GI sheets: 0.80 m gross width provides 0.70 m effective cover with a 1½ corrugation side lap (or 0.60 m with 2½ corrugations). Standard lengths are 5 to 12 ft. Rows along the slope require a 0.25 m (10-inch) end lap: Rows = ⌈(Slope − 0.25) ÷ (Sheet Length − 0.25)⌉. Sheets = ⌈Roof Length ÷ Cover Width⌉ × Rows × Sides.
    • Long-span rib-type: 1.00 m effective cover width (sold by the linear metre). Sheets run seamless from ridge to eave: Sheets = ⌈Roof Length ÷ 1.00 m⌉ × Sides, each ordered to Slope + 0.05 m overhang.
    • Hip roofs: The four sloping facets add up to a gable roof of the same plan dimensions plus a 10% waste allowance for diagonal cuts at hips and valleys.
  3. Calculate C-purlins (2" × 4" C-purlins, 6 m)

    Purlin lines run perpendicular to the slope, spaced at 0.60 m on center. Each commercial 6 m C-purlin provides 5.8 m of effective coverage after splicing over roof trusses:

    Purlin Lines = ⌈Slope ÷ 0.60 m⌉ + 1

    Commercial Purlins = Purlin Lines × ⌈Roof Length ÷ 5.8 m⌉ × Sides

  4. Calculate tek screws and accessories

    Self-drilling 2½" tek screws with neoprene EPDM washers fasten sheets to steel purlins:

    • Tek screws: 8 screws per m² for corrugated GI; 7 screws per m² for long-span rib-type.
    • Ridge and hip rolls (2.4 m): Spliced with a 0.15 m lap, giving 2.25 m effective cover: ⌈(Ridge + Hips) ÷ 2.25 m⌉.
    • Gutters & downspouts: Eaves length in metres; downspouts at ⌈Eaves ÷ 10 m⌉ × Height (3 m).

The tek-screw, ridge-roll and downspout figures are derived or general rules of thumb, not PH manufacturer data.

Worked example

A gable roof 10 m long, with rafters that run 4 m on plan from the eaves to below the ridge on each side, at a 4:12 pitch:

Material Calculation To order
Slope length 4 m × 1.054 (4:12) 4.22 m
Roof area 10 m × 4.22 m × 2 sides 84.3 m²
Long-span sheets ⌈10 ÷ 1.00⌉ × 2 sides, each 4.22 + 0.05 m 20 sheets, 4.27 m long
Corrugated GI, 8 ft (2.44 m) ⌈10 ÷ 0.70⌉ = 15 across × ⌈(4.22 − 0.25) ÷ (2.44 − 0.25)⌉ = 2 up × 2 sides 60 sheets
C-purlins, 6 m (⌈4.22 ÷ 0.60⌉ + 1) = 9 lines × ⌈10 ÷ 5.8⌉ = 2 × 2 sides 36 pieces
Tek screws 84.3 m² × 7 (long-span) or × 8 (corrugated) 591 or 675
Ridge rolls, 2.4 m ⌈10 m ÷ 2.25 m⌉ 5 rolls

Long-span needs no end laps, so it takes fewer, longer sheets and fewer screws. The app prices the result from its regional price book.

Roofing factors

The cover widths, laps, purlin spacing and fastener ratios behind the example:

Estimating Component Standard Rule / Parameter Application Method
Corrugated GI Cover Width 0.70 m (1½ corrugation lap) Standard side lap (0.70 m), or 0.60 m with 2½ corrugations
Long-span Cover Width 1.00 m effective width Full continuous lengths cut to slope order
Corrugated End Lap 0.25 m (10 inches) Required between overlapping sheets along the slope
C-Purlin Spacing 0.60 m on center 0.60 m, from a DPWH house plan; follow your plans
Fasteners (Tek Screws) 8 / m² (corrugated), 7 / m² (long-span) 2½" self-drilling screws with neoprene washers
Ridge & Hip Rolls 2.25 m effective per 2.4 m roll 0.15 m overlap at joints
Hip Roof Allowance Gable equivalent + 10% Covers diagonal cuts along hips and valleys

Instead of manual geometric trigonometry, the Countstruct roofing calculator works out slope dimensions, sheet numbers, purlins, and accessories from basic plan entries. The app prices the result from its regional price book.

Back to the calculator ↑

What the Countstruct calculator adds

Countstruct Roofing Calculator Features

  • Preset roof geometry: gable, shed (lean-to), or complex 4-sided hip roofs with overhangs and pitch factors.
  • Instant slope trigonometry from horizontal plan spans and standard rise-to-run pitch ratios.
  • Support for modular corrugated GI sheets (5 to 12 ft stock lengths) or seamless roll-formed long-span roofing.
  • Integrated scheduling of 2" × 4" C-purlins, tek screws, 2.4 m ridge/hip rolls, and eaves drainage gutters.
Open the roofing calculator in Countstruct

Questions

Why choose long-span roofing over corrugated GI sheets?

Long-span sheets are sold by the metre and run one piece per slope (each ordered to slope length + 0.05 m), avoiding the 0.25 m end laps required when overlapping corrugated sheets.

What is the difference between 1½ and 2½ corrugation side laps?

Corrugated GI sheets are 0.80 m wide. A 1½ corrugation side lap covers 0.70 m (the app's default), while a 2½ corrugation side lap covers 0.60 m.

Why are roof purlins spaced at 0.60 metres?

A purlin spacing of 0.60 m is the app's default, taken from a DPWH house plan. Follow the spacing on your structural plans.

How many ridge rolls do I need?

Ridge and hip rolls come in 2.4 m pieces, calculated as ⌈(ridge + hips) ÷ 2.25⌉. The 2.25 m effective coverage is a rule of thumb allowing for laps.

How many long-span roofing sheets do I need?

Divide the roof length by 1.00 m, round up, and multiply by the number of sides. A 10 m gable roof needs 10 sheets per side, or 20, each cut to the slope length plus 0.05 m.

How many tek screws per sheet of roofing?

Count by area instead: about 8 tek screws per m² for corrugated GI and 7 per m² for long-span. An 84 m² roof takes about 675 screws for corrugated and 591 for long-span.

How do I compute the slope length of a roof?

Multiply the horizontal run (from the eaves to below the ridge) by the pitch factor √(1 + (rise ÷ run)²): 1.031 for 3:12, 1.054 for 4:12 and 1.118 for 6:12.